We have different oxygen sensor:also we custom any oem
oem: 234-4012, 234-4215, 234-4076, 234-4078 126-73134
for different car:GMC Chevrolet Silverado 1500 Tahoe Avalanche 15284
Dodge Chrysler Ram Jeep 11-17
1999-2003 Ford Mustang 3.8L 4.6L 234-4046 234-4610
234-4251 Downstream O2 Oxygen Sensor FITS 08-12 Chevrolet Malibu Equinox 2.4
Oxygen Sensor 234-4874 For Audi A4 S4 A6 VW Beetle Phaeton Passat Jetta Golf
Ford Taurus Explorer E-150 F-150 Escape Mercury Lincoln Oxygen 02 Sensor
02 Oxygen Sensor 234-4018 Downstream For Chevrolet Express 1500 2500 3500
Upstream Oxygen Sensor 234-4012 For Chevrolet Express GMC Truck Van Isuzu Acura
Rear Oxygen Sensor 234-4215 For Toyota Highlander Supra Lexus RX300 89465-49075
Oxygen O2 Sensor For Jeep Cherokee Wrangler Grand Cherokee 4.0L 1997-1999
234-4078 Up/Downstream Oxygen Sensor For Jeep Cherokee Grand Cherokee 96-01 4.0L
Auto Sensor oil pressure sensor 12673134
Q: How do I know the O2 sensor is good or
not?
A: The only way to know if the O2 sensor is
functioning normally is to check its responsiveness to changes in the air/fuel
mixture, by Voltage Measurement or Waveform Simulation.
Use a 10-megaohm digital voltmeter. Hook up
the voltmeter's red probe to the sensor's signal wire and the black probe to engine
ground. (Use back probe method, DO NOT pierce the wire.) For a good sensor,
voltage should fluctuate constantly between 0.1 and 0.9 volts after starting
the engine for 2 or 3 minutes.
Please take a video clip of the voltmeter
and contact us if our sensor:
Goes above range between 0.1 and 0.9 volt
Remains below 0.5 volts
Stays fixed at a particular voltage
You're free to choose replacement or refund
if our sensor fails to work, in this case.
Oxygen Sensor,Silver Oxygen Sensor For Cars,90 Degree Oxygen Sensor,Front Auto Oxygen Sensor Dongguan Jiaxing Precision Machinery Co., Ltd. , https://www.jiaxautoparts.com
Why are there no Chinese competitors competing for the project? The root cause is that there is no similar product in China. Although the quality and quality of some domestically-made welding equipment have approached the international advanced level, overall, the gap between the instability of domestic welding equipment product quality and foreign equipment is still quite large. At present, the high-end market is basically the world of imported products, and domestic products can only compete fiercely in the low-end market.
In addition, there are a large number of companies in the welding equipment industry in China, and most of them have weak development capabilities. They can only expand simple reproduction to seize market share and have a serious excess production capacity. Special products, especially high-end special welding machines and complete sets of welding equipment are being developed. And the production capacity is relatively low, basically can not be mass produced or the quality is far from the imported product, and can only rely on imports.
However, with the improvement of China's industrial level, China's welding industry has ushered in a lot of new opportunities for development. It is not out of reach to “get fit and healthy†to get rid of the current days of dependence on imports.
Among them, the development of steel and other upstream products has stimulated the rapid development of the welding equipment industry. Welding equipment is based on steel as the main welding target, and the growth of steel products will inevitably drive the development of China's welding equipment industry.
At the same time, the demand for dedicated, special, complete sets, and production line welding equipment required by the national key projects will continue to increase. If our companies can work stably and improve product quality, they will greatly increase market share.
Under the circumstances of a good environment, if China's welding industry wants to achieve sustainable and leapfrog development, it will be difficult for the welding equipment industry to rely solely on its own capital and strength, or rely solely on imported materials and devices to achieve product renewal and rapid development. .
Therefore, our welding company must survive and develop. It is worth mentioning that mergers and consolidations among enterprises will enable some large domestic companies to gradually become stronger and create state-owned brands.
Domestic welding equipment to survive and develop, but also rely on their own
The only bidder used for the West-East Gas Transmission Project's self-shielded flux-cored wire products was a U.S. company's product. The price of self-shielded flux-cored welding wire was around RMB 60 per kilogram. This price was close to the price of protecting the stainless steel flux-cored wire. .