Turning rolls refers to the use of welding pieces and the friction between the active roller to drive the cylindrical welding device rotation device. Self-adjusting turning roller for circular tube welding, the distance between the rollers can be adjusted according to the size of the cylinder, a variety of specifications for the user to choose the turning roller.
As per the market demanding, we have developed and designed kinds series of turning rolls to satisfy the customer`s requests, such as KT series adjustable turning rolls, KTS serise manual adjustable turning rolls, KTD series electric adjustable turning rolls, KTF series heavy duty anti-creep adjustable turning rolls and ZT series self-aligning turning rolls. As per the customer`s requests, we can design ang manufacture non-standard turning rolls, such as turning rolls with trolley, inclining turning rolls, hydrulic elevation turning rolls and assembly turning rolls and so on.
KT Series Adjustable Welding Turning Rolls
Composition and characteristics of the welding turning roller
1 The KT adjustable turning rolls include one power bed and one idle bed.The turning rolls below 40T adopt helical-worm &cycloidal pin wheel decelerator,and over 40T adopt cycloidal pin wheel or helical-worm decelerator.
2 The series turning rolls adopts screw to adjust,available for changes of workpiece diameter,simple structure and economy
3 The wheels are new combination style ,one rubber wheel and two steel wheels,with big load capacity ,big friction,strong drive and glue force
4 Imported transducer realized the stepless regulation with wide speed range ,high precision and big starting moment
5 The control system has the synchronized linkage interface with manipopulator and has remote controller ,easy and reliable.
ype
Load
(t)
Line speed
(mm/min)
Workpiece diameter(φ)
Wheel Size(mm)
Power(KW)
Size(mm)
Input voltage
Dia.
Wid.
L
W
H
KT-3
3
100-1000
250-2500
250
140
0.18*2
1977
468
375
Three-phase 380v
KT-5
5
100-1000
250-3000
250
140
0.25*2
2760
470
415
KT-10
10
100-1000
300-3500
300
170
0.37*2
2920
525
535
KT-20
20
100-1000
400-4500
350
180
0.55*2
3010
540
635
KT-30
30
100-1000
400-4500
350
180
0.75*2
3030
610
635
KT-40
40
100-1000
500-5000
400
200
0.75*2
3335
915
695
KT-50
50
100-1000
500-5000
450
220
1.10*2
3400
1055
810
KT-60
60
100-1000
500-5500
450
220
1.10*2
3570
1055
810
KT-80
80
100-1000
800-5500
500
240
1.50*2
3520
1130
900
KT-100
100
100-1000
800-5500
500
240
2.20*2
3450
1150
900
KT-200
200
100-1000
800-6000
600
240
2.20*2
4250
1190
1050
KT-300
300
100-1000
1000-6500
640
250
3.00*2
5400
1320
1150
KT-500
500
100-1000
1000-8000
700
300
5.50*2
6200
1580
1460
KT-800
800
100-1000
1000-8000
800
350
11.0*2
6880
1900
1825
Welding Turning Rolls Welding Turning Rolls,Pipe Turning Rolls,Ransome Turning Rolls,Tank Turning Rolls SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachine.com
Second, the charge, filling: must be carried out before the charge to clean up the blast hole, using bamboo sticks charge, prohibit charge with an iron rod. When charging, fireworks are prohibited and open flames are prohibited. During the expansion of the pot, the time interval between the expansion of the pot must be greater than 15 minutes to prevent the blasthole temperature from being too high, leading to early explosion; in addition to the deep blasting, any blasting must be filled with the pharmacy. The tamping should be very careful and must not be destroyed. Detonate the network and lines.
Third, the establishment of warning: sound and visual signals must occur at the same time before blasting, so that people in the danger zone can clearly hear and see, underground blasting should set up sentries on the relevant channels, ground blasting should be at the boundary of the danger zone Set up guard posts so that all channels are under surveillance and evacuate all personnel in the blasting danger zone.
4. Ignition, connection and detonation: The fuse shall be used for detonation. It shall be carried out by not less than two persons, and must be ignited by a fuse or a special ignition device. When a single ignition occurs, the number of consecutive ignitions of one person shall not exceed 5 underground explosions, and the number of open explosions shall not exceed 10. The length of the fuse should be such that after the completion of the fuse, the personnel can be evacuated to a safe place, but not less than 1.2 meters.
When the electric detonator is used to detonate, the electric detonator must be turned on one by one, and the electric detonator used in the same blasting network should be the same model of the same factory. Before the main line of blasting is connected with the blasting power supply, the total resistance value of the whole line must be measured. The error between the total resistance value and the actual calculated value must be less than ± 5%. Otherwise, the connection is prohibited. Large blasting must use a double detonation line. When gas and coal dust explosion hazards in mines detonated using electricity, except for the use of explosion-proof detonator as detonation power.
Sixth, blind cannon treatment: The blind cannons produced by the explosion contain guns and cannons. If a blind cannon is found and a blind cannon is suspected, it should be reported immediately and dealt with promptly. If it cannot be disposed of in time, it should be clearly marked and appropriate safety measures should be taken to prohibit the ejection or pulling of the detonation kit, and it is strictly forbidden to kill the eye. The main methods of blind cannon are:
(1) After inspection, it is confirmed that the detonation line of the blasthole is intact and missed, and the explosion is caused by the leakage ignition, and the detonation can be performed again.
(2) The parallel eye charge is detonated. For shallow blasting, parallel eye distance blind blasthole shall not be less than 0.3 m, and deep hole blasting parallel eye distance blind blasthole shall not be less than 10 times the blasthole diameter.
(3) Using a tool made of wood, bamboo or other materials that are not ignited, gently pour out most of the stuffing in the blasthole and use a concentrating drug pack to induce the blast.
(4) If the explosive used is non-water-resistant ammonium nitrate explosive, part of the stuffing may be taken out and water is poured into the hole to invalidate the explosive. 
Prevention of mine blasting accidents
First, in strict accordance with the operating procedures: blasting operations personnel must obtain the qualification of the blasting staff; all kinds of blasting must be prepared blasting design book or blasting instructions. The design book or instruction manual shall have specific blasting methods, blasting sequence, charge amount, ignition or connection method, warning safety measures, etc.; during the blasting process, the unrelated personnel must be evacuated. Strictly observe the safety regulations and safety operation rules for blasting operations.
5. Post-explosion inspection: After blasting, after a period of time (open-air blasting is not less than 5 minutes, underground blasting is not less than 15 minutes, and ventilation is required to blow off the gun smoke), and then confirm the blasting site safety, after the blasting command or When the blasting squad leader agreed to issue a warning signal, the personnel were allowed to enter the blasting site.